To date I've purchased teeth from other craftspeople to use in my masks, but I've always really wanted to make my own. Below, a pile of attempts made over the past couple of years, made with Monster Clay (a kind of plasticine), Super Sculpey and Apoxie Sculpt.(Skully is supervising. He is a very helpful skull.) A whole lotta nope right here.

I finally settled on the Monster Clay for making the prototype teeth. I got tired of waiting for the other two to dry and/or set up in between sculpting sessions, and I got REALLY tired of trying to smooth out the hardened model with sandpaper or a Dremel. Monster Clay can be frozen to make it very hard and  can be softened with a hairdryer or microwave or such to make it very soft, so it is adaptable for a variety of sculpting situations. It also smooths beautifully using rubbing alcohol or its more powerful big brother, isopropyl myristate.

 

  

Above, looking to see how the lower part of the jawset is shaping up when viewed from the side. The teeth are just loosely stuck down to the gums at this point, so I can easily move them around if I need to.

 

And tada! Above, a finished Monster Clay plasticine model, ready for molding. Silly me, little did I realize that this would be the first of three finished jawsets I would mold. Sucks being a perfectionist.

Above, beginning the molding process, and a tongue while I'm at it. The jawset has been firmly attached to a thin piece of plywood, which will serve as a mold board. Every little gap between the model and the mold board is filled in, as otherwise the mold rubber could find its way under the model, and float the model up on top of it while it's curing. Which would not make a very good mold at all.

Above, getting ready to revise the jawset. Did I mention how I did this three times? Seriously though, it's easier to check the fit of the teeth in the head when they're in hard resin and not squishable clay. Above, a set of resin teeth that has been Dremelled down to fit the head better, and another set of clay teeth made by pouring melted Monster Clay into the mold, called a "borrowed casting". It's much easier to tweak the teeth from a borrowed casting than trying to make a whole new set from scratch. (If I wasn't such a chicken, I could have also resculpted my original set of clay teeth. But I wanted to keep them the way they were for extra insurance.) 

Above, revisions. To the right in both pictures is the original sculpt, still on the moldboard. In the middle is a modified resin casting, and to the left is the resculpted "borrowed casting". This first go round I removed the "flare" thingy from the bottom jaw, as it only really served to complicate fitting it into the resin head. I also made the plate for the upper jaw more symmetrical. You can see how the original sculpt has a bigger "bulge" on the left hand side than the right. Why did I do this, you may ask. Well, I was using a reject resin head casting to fit the teeth in, and I forgot that the resin on one side of the muzzle was much thicker than that on the other so.... in order to center the teeth in the opening, the plate had to be a lot wider on one side. Definitely not going to be the case with the average resin head! Fortunately I realized this before I got too much further into this process!  A great big duh, but could have been a much bigger duh.

Above, showing all three sets of revised teeth. The top set is the first one, the middle is the second and the set on the bottom is the final version. Besides changing the "plate" as described earlier, I did a lot of playing with the front incisors. I refined them in the second set but then realized I had also made the top ones too small, so I made them bigger in the third set. After re-checking my reference pictures of real wolves I also decided the gum area above the front incisors also needed to be longer, so I also changed that in the third set. I also did a lot of fiddling with the area circled in yellow in the right hand picture, with the way those particular teeth came together. The top incisor right next to the large bottom canine also underwent a fair bit of refinement.

And since I had spent so much time fiddling with the teeth, I decided to fiddle with the mold making method as well. At the suggestion of an acquaintance I made my next set of mold boxes out of Legos instead of Tupperware containers, so I could get the mold boxes precisely the size I needed them and save molding rubber. Molding rubber is expensive. They don't call it "platinum cure silicone" for nothing. (A good source of cheap used Legos is bricklink.com.)

 

Above, the nose and tongue models with their squishy rubber counterparts. Wheee!!!

Checking out the fit of the rubber nose in a resin head. Lookin' good! The resin head on the right wants a rubber nose too. 

And above, a pile o' puppy parts, ready for maskmaking!! I'm feeling good about the results of my endeavors here. Time to think about colors for fur!!

​​I also wanted the teeth to sit up much higher in the lower jaw than they did in my first head, as they kinda disappeared into lips and fur after I got it assembled. I played a lot with layers of Foamies underneath the teeth to get them exactly where I wanted them, and so far I'm happy with how they look.

As with the previous head, I've been referring to the DVC tutorials online as I work on this head, and much to my confusion they've started redoing that series- when I did the first mask, the lips were applied last, after the airbrushing, and now they're applied early in the process, along with the eyelids. Maybe they were done last in the first series so that airbrush overspray wouldn't get on them, but that's easy enough to paint over with black paint. In any case it was a pain to apply them with fur already there, and so far I like this way better.
​

​I also learned the hard way it's best to cut the cast up right before assembling it. I was so excited to get a good cast I couldn't wait to open the eyes up and hinge the jaw, and then I let the head sit, and sit, and sit.... and the jaw warped, shifting to one side. Now the head has an expression kinda like this: :-/ Nothing that can't be fixed with a Dremel and some epoxy, but still, something I'd rather avoid in the future.

Above, working out how to resculpt the jaw to make it look straighter. I often take a photo of an area I'm working on, print it out and draw on it, to help visualize what I should do. In the printout /drawing to the right, I've decided to dremel off the lip outside of the thick blue line. Another point for adding the lip early on- it gave me a way to tweak the jaw I wouldn't have had otherwise.

(And... one day I went down into the basement to work, and I found my daughter had gotten into my packing peanuts....)

Above, the lower jaw resculpted and straightened out a bit. I think it looks much better. Neatening up the edge of the lower lip helped a bit too.

Above, chiffon added to one tear duct but not yet the other, as modelled by my packing peanut loving daughter. Freaky deaky!

​Two takeaways for the next resin base sculpt:

First, make sure the areas in which the eyes will be glued are as flat as possible and in the exact same plane with each other. Any crookedness or unnevenness in these areas will be greatly exaggerated when the resin eyes are in place, and gives the mask a rather wall-eyed, inbred expression. Next base sculpt, I think I'll use metal or rigid plastic discs of the correct size to mark out these areas and leave them there while moldmaking, to make sure those areas don't squish out of shape. I was able to glue the eyes into this base to my satisfaction using bits of resin and hot glue to level them out, but care taken with the next sculpt could definitely make the process a lot easier. 

Second, sculpt the next head so that it can easily take a nose with a flat back. DVC noses, and I suspect any other noses that are cast separately and glued on to a base later, have flat backs. I suspect they are made in one piece molds, the backs of which are open so that the casting material can be poured in, which then levels out as it sets. When I removed the nose on this base to accommodate the DVC nose, I was left with an awkwardly shaped hole into which to glue it. I re-sculpted the area a bit with epoxy so that the nose would fit (the thick black band behind the nose in the pics is epoxy for the most part) and so all is well that ends well, but again, this is something to take into consideration for future head sculpts.

Next, ears!!

​