 | So I've made two heads, and now I want to learn to make tails and paws to go with them!! Whee!!! My last blog post covered my tail making adventures, now it's time to move on to paws. Here, my daughter and her BFF model the first two sets I made. |
 | While in theory it should not have been too difficult to make a pattern for a tail, I wound up going through three versions before I came up with one I liked. So I was delighted to find Freakhound's free and extremely cool paw patterns online. As it was, I was going to have to learn a ton of new skilz in order to make handpaws, so it was really nice to have that one less thing to worry about. Click here if you want to check the patterns out. |
| Some of the things I learned included using bias tape to edge the cuff (Matrices' tutorial here) and appliquing toebeans (Matrices' tutorial here) (and Kloofsuits' here). While Freakhound's pattern includes pretty complete instructions, I also got a lot of good information on general construction from Kloofsuits's two handpaw tutorials (part one) and (part two). These include instructions for doing the toebeans as little "pillows" sewn into the hand instead of applique, and a very good demonstration on making liners. One thing I haven't found anywhere, however, is clear instructions on adding resin claws. All the instructions I have found are for sewn, fabric claws. So I'll have to figure that out for myself. Supposedly it's just cutting a hole in the fingertips and gluing them in, right? |   |
My first pair of practice handpaws, made out of my "cheap" white fur. The toebeans are appliqued vinyl, the claws are resin. The cuffs have a bias tape edging and no lining, since early on in my online explorations I had read that linings were a luxury, good only for retaining sweat. However I found the resin claws made the tips of the fingers floppy and stuffing was helpful in stiffening them. And a liner is useful in separating the stuffing from the hands. Which brings me to...
My second pair of practice handpaws. These do have a lining as well as the bias tape edging. The toebeans are felt "pillows" sewn into the white fabric, a method Kloofsuits describes in her tutorials above. This method needs less skill than applique to yield a very nice result, though it takes much more time and patience. (This is what podcasts are for!) Even though these were just practice handpaws I wish I had used fabric other than felt, as it pilled all to hell in about two seconds and looks awful. At this point I'm also feeling frustrated by the claws. They look crooked and haphazard in both sets of paws, pointing in whichever direction they feel like when I glue them in, no matter how careful I try to be.
 | So down into the basement I go to sculpt, mold and cast new claws. I based these on the claws in Freakhound's pattern hoping they would better harmonize with the overall handpaw design. I made the originals out of Apoxie Sculpt and polished them to a high shine using the Novus plastic polish system. I made two modifications to the bases of the claws in the hope that they'd more likely to wind up straight in the fingertips: I made them oval, not round, so I could tell which were the tops and undersides of the claws from the inside of the paw, and I drilled holes in them for stitching the claws in to the paws to keep them steady while gluing. |
And the a third set of paws, this time made of "good" fabric, with faux suede sewn-in "pillow" toe beans and the new resin claws. I'm pretty happy with how these look.
| These paws also have a different kind of cuff than the bias tape edging that Matrices demonstrates. I was OK with less than perfection with the two practice sets of handpaws, but since I'm hoping to sell them I wanted these black handpaws to be perfect. The bias tape edging defied me four times on these paws, and four times I ripped it off. I wound up buying Kloofsuit's deluxe handpaw pattern just for the instructions on this kind of cuff, and I'm very happy I did. The download is available to purchase here. |  |
And, giving the handpaws a try!
RSS Feed